Replacement Parts

Replacement pair of black clamps for M0 6.5” Element Ready™ moto-can speakers. See COMPATIBILITY chart to verify fitment before purchasing.

Single replacement black clamp for M0, M1, or M2 6.5” moto-can speakers. If both of your clamps are broken, you will need to buy 2 of these. See COMPATIBILITY chart to verify fitment before purchasing.

Replacement hardware kit for Harley-Davidson aftermarket saddlebag subwoofer kit. If your saddlebag gets damaged, this kit will allow you to transfer the components to your new replacement saddlebag. See COMPATIBILITY chart to verify fitment before purchasing. Kit includes everything from original 1315-75758-01 Accessory Pack: (12) Nylon zip ties 8 in (8) Phillips screws M3 x 0.5 x 12 mm (1) Hole saw OD 45 mm (4) Washers OD 9 x ID 3.2 x T0.8 (4) Hex screws 3/16 in, 5/16-18 thread, 1.25 in (4) Clip 5/16-18 thread (2) Screw M3 x 0.5, 5 mm (8) Screw thread cutting ST3.0, 6 mm (2) Nylon plug ID 0.75 in (2) Hex nut M3 x 0.5 (8) Phillips screw #8 x 0.75 in. (1) Hex wrench 3/16 in (2) Alcohol wipe

Replacement IPX6 covers for M5-800X4, M5-1000X1, M5-1500X5 amplifiers. Kit includes (1) M5-800X4 smoked cover, (1) M5-1000X1 smoked cover, and (1) M5-1500X5 smoked cover with mounting screws as shown in photo. Individual covers not sold separately.

Signal input extension, speaker output extension, and power input extension harnesses to make remote connections on M5 amplifier. Provides only extension harnesses and mounting screws as pictured. Does NOT include actual power connector, RCA harness, or speaker harness.

Signal input extension, speaker output extension, and power input extension harnesses to make remote connections on M5 amplifier. Provides only extension harnesses and mounting screws as pictured. Does NOT include actual power connector, RCA harness, or speaker harness.

Signal input extension, speaker output extension, and power input extension harnesses to make remote connections on M5 amplifier. Provides only extension harnesses and mounting screws as pictured. Does NOT include actual power connector, RCA harness, or speaker harness.

Replacement hole saw and grommets for RNGR18, Pro XP, Turbo R, and Pro R stage kits, subwoofer kit and Road King kits for Harley-Davidson®. See COMPATIBILITY chart to verify fitment before purchasing.

Replacement hardware accessory pack for compatible aftermarket Pro XP, Turbo R, and Pro R stage kits. See COMPATIBILITY chart to verify fitment before purchasing.

Accessory pack for the PMX-HD14 includes these components: (1) Road Glide trim panel(1) Street Glide trim panel(8) Trim Panel Screws (1) Mini Phillips screwdriver for trim panel (4) Radio Chassis Mount screws (8) Rubber sleeves for radio chassis screws

This is a replacement bass level control for Jeep Audio Kits. This is a custom designed PLC2 that allows full linear control of the bass level through the digital signal processor. Please check compatibility charts on Jeep Kits for fitment.

Replacement USB male-to-male cable for 3Sixty.3

1st generation quick disconnect speaker wiring harness for M2 and PM wake tower speaker enclosures.

Replacement Ride Command Harness for RZR19PXP Kits. This all-in-one signal harness includes an active noise suppressor designed to eliminate turn-on/off pops while providing the same low level output as if a PMX source unit was installed.

Replacement RCA signal harness for PMX-HD9813 source unit. The harness features the following connections:• FRONT LINE OUT (left/right RCA)• REAR LINE OUT (left/right RCA)• SUB LINE OUT (left/right RCA)• AUX INPUT (left/right RCA)• Blue Remote Turn-On WireSee COMPATIBILITY chart to verify fitment before purchasing.

Replacement main power harness for RZR19PXP and RZR19RCPXP stage kits. Provides power, ground, remote turn-on, signal routing, and speaker wires for STG4, STG5, and STG6 audio kits. Please refer to compatibility chart to verify fitment before purchasing.