1 / 5

Audison

APS10DAPS10D 250 mm Subwoofer

Ultra-low profile (4.7 in. / 120 mm) for maximum installation flexibility. Designed to deliver maximum performance in a sealed enclosure starting from 10 lt.

Highlights

  • Ultra-low profile (4.7 in. / 120 mm) for maximum installation flexibility.
  • Designed to deliver maximum performance in a sealed enclosure starting from 10 lt.
  • Special designed cone-dustcap-basket geometry which guarantees a long linear excursion capability (11 mm, one-way) while keeping the mounting depth to minimum.
  • Air vents on the basket underneath the spider, eliminating the need for the central pole vent allowing mounting close to rear wall of enclosure.

Key specs

Full specs
Nominal diameter
250 mm (10 in)
Impedance
4+4 Ohm
Power Handling - Peak
800 W
Power Handling - Continuous
400 W
Sensitivity
84 dB
Voice Coil Ø
60 mm
Magnet Material
HIGH DENSITY FLUX FERRITE
Magnet size D x d x h
140 x 70 x 30 mm

Key specs

Full specs
Nominal diameter
250 mm (10 in)
Impedance
4+4 Ohm
Power Handling - Peak
800 W
Power Handling - Continuous
400 W

Highlights

Overview
  • Ultra-low profile (4.7 in. / 120 mm) for maximum installation flexibility.
  • Designed to deliver maximum performance in a sealed enclosure starting from 10 lt.
  • Special designed cone-dustcap-basket geometry which guarantees a long linear excursion capability (11 mm, one-way) while keeping the mounting depth to minimum.
Overview
  • Ultra-low profile (4.7 in. / 120 mm) for maximum installation flexibility.
  • Designed to deliver maximum performance in a sealed enclosure starting from 10 lt.
  • Special designed cone-dustcap-basket geometry which guarantees a long linear excursion capability (11 mm, one-way) while keeping the mounting depth to minimum.
  • Air vents on the basket underneath the spider, eliminating the need for the central pole vent allowing mounting close to rear wall of enclosure.
  • Massive motor assembly, optimized with FEM (Finite Element Modeling) for perfect control under high power, high excursion conditions.
  • Water-repellent pressed paper 10 in. cone, featuring a profile developed with FEM simulation and optimized with the Klippel Scan Vibrometer.
  • Dual voice coil design specifically developed to be combined with either AF C4.10 bit (2 CH + 2 CH bridged), AF M5.11 bit (Sub CH) or AF C4D/AF M4D (2 CH bridged) amplifiers.
  • Steel mesh grille and plastic gasket included.
  • The APS 10 D is designed to deliver maximum performance in a sealed enclosure with ultra-compact volumes, from 10 lt. to 12 lt. The dual voice-coil and single voice coil versions feature push connectors for ease of wiring and configurations. Prima subwoofer components have been developed with a primary goal: to deliver high output in tight spaces. Output is a matter of excursion; the more air the cone moves, the more output. However reduced mounting depth traditionally has meant low excursion. Prima subwoofers employ a special cone-dustcap-basket geometry which guarantees large excursion of the mobile group, while keeping the mounting depth to a minimum. The surround and spider have been carefully designed to prevent the rocking-mode phenomenon. The cooling circuit has been designed with air vents on the basket underneath the spider, eliminating the need for vents on the bottom-plate. This allows the subwoofer to be mounted close to the back wall of the enclosure, making the most of the reduced mounting depth.
Highlights

Key features

  • Ultra-low profile (4.7 in. / 120 mm) for maximum installation flexibility.
  • Designed to deliver maximum performance in a sealed enclosure starting from 10 lt.
  • Special designed cone-dustcap-basket geometry which guarantees a long linear excursion capability (11 mm, one-way) while keeping the mounting depth to minimum.
  • Air vents on the basket underneath the spider, eliminating the need for the central pole vent allowing mounting close to rear wall of enclosure.
  • Massive motor assembly, optimized with FEM (Finite Element Modeling) for perfect control under high power, high excursion conditions.
  • Water-repellent pressed paper 10 in. cone, featuring a profile developed with FEM simulation and optimized with the Klippel Scan Vibrometer.
  • Dual voice coil design specifically developed to be combined with either AF C4.10 bit (2 CH + 2 CH bridged), AF M5.11 bit (Sub CH) or AF C4D/AF M4D (2 CH bridged) amplifiers.
  • Steel mesh grille and plastic gasket included.
Specs

Technical Specs

12
Nominal diameter250 mm (10 in)
Impedance4+4 Ohm
Power Handling - Peak800 W
Power Handling - Continuous400 W
Sensitivity84 dB
Voice Coil Ø60 mm
Magnet MaterialHIGH DENSITY FLUX FERRITE
Magnet size D x d x h140 x 70 x 30 mm
Cone MaterialWATER REPELLENT PRESSED PAPER
Xmax12.6 mm (0.5 in)
Xmech18 mm (0.71 in)
Driver Displacement Volume1.12 l (0.04 ft)

Electric-acoustic Specs

10
Re2.2 Ohm
Fs27 Hz
Le1.5 mH
Vas41 l (1.448 ft)
Mms170 g (5.997 oz)
Cms0.2 mm/N
BL10.4 T•m
Qts0.52
Qes0,58
Qms4.7

General

1
Weight5.24 kg

Dimensions

5
Dimension A270 mm (10.63 in)
Dimension B233 mm (9.17 in)
Dimension C105 mm (4.13 in)
Dimension D88 mm (3.46 in)
Dimension C1119 mm
Reviews (0)

No average rating yet

0 reviews

No written reviews are live yet. Signed-in customers can submit one below.

Own this product?

Share installation notes, sound quality feedback, and fitment tips. Customer reviews are saved in the same database and go live after moderation.

Checking account status...

No written reviews are live for this item yet.

Support